RANCANG BANGUN SISTEM PENGENDALI SUHU BARREL PADA MESIN SINGLE SCREW EXTRUDER MENGGUNAKAN METODE PID BERBASIS ESP32

Authors

  • Yani Prabowo Universitas Budi Luhur
  • Anwar Rifai Universitas Budi Luhur
  • Jan Everhard Universitas Budi Luhur

DOI:

https://doi.org/10.36080/skanika.v9i2.3773

Keywords:

single screw extruder, pengendalian PID, ESP32, suhu barrel, proses ekstrusi

Abstract

Barrel temperature stability is a crucial factor in the polymer extrusion process, as temperature fluctuations directly affect melt viscosity and final product quality. This study designed a temperature control system for a single-screw extruder using an ESP32 microcontroller to compare the performance of the Proportional-Integral-Derivative (PID) method against a system without control (open loop). The research methodology involved testing various screw rotation speeds from 50 to 200 RPM to observe barrel temperature stability and melt homogeneity. The determination of the PID parameters in this study was based on the evaluation of the open-loop system's thermal response mapping, yielding optimal tuning values of Kp = 4.8, Ki = 0.09, and Kd = 55. The test results showed that the system without control experienced temperature fluctuations of ±8–12°C, while the PID controller successfully maintained temperature stability with a low deviation of ±1–3°C. Furthermore, the PID system was able to automatically compensate for temperature increases caused by material friction at high speeds. The implementation of PID control was proven to increase thermal stability by up to 80% compared to conventional systems. These results demonstrate that the use of PID algorithms on microcontrollers ensures a more precise and stable plastic extrusion process compared to traditional methods.

Downloads

Download data is not yet available.

References

[1] H. L. Chen, et al., “The plastic waste problem in Malaysia: management, recycling and disposal of local and global plastic waste,” SN Appl. Sci., vol. 3, no. 437, 2021, doi: 10.1007/s42452-021-04234-y.

[2] L. Makarichi, W. Jutidamrongphan, and K. Okpara, “Choosing among plastic waste management options: lessons from Zimbabwe’s plastic waste flows,” J. Mater. Cycles Waste Manag., vol. 27, no. 1, pp. 597–615, 2025, doi: 10.1007/s10163-024-02132-0.

[3] N. F. Pambudi, et al., “Enhancing public participation in plastic waste management for a sustainable circular economy: insights from Indonesia,” J. Mater. Cycles Waste Manag., vol. 27, no. 5, pp. 3366–3389, 2025, doi: 10.1007/s10163-025-02294-5.

[4] R. A. Maulana and W. Windarto, “Rancang Bangun Pemilah Sampah Organik Dan Non Organik Berbasis Mobile Di Medang Lestari,” SKANIKA Sist. Komput. dan Tek. Inform., vol. 7, no. 1, pp. 12–21, 2024, doi: 10.36080/skanika.v7i1.3147.

[5] M. G. Kibria, N. I. Masuk, R. Safayet, H. Q. Nguyen, and M. Mourshed, “Plastic Waste: Challenges and Opportunities to Mitigate Pollution and Effective Management,” Int. J. Environ. Res., vol. 17, no. 20, 2023, doi: 10.1007/s41742-023-00507-z.

[6] D. Kwon, et al., “Thermochemical methanolysis-based recyclability of polyethylene terephthalate (PET) via pseudo-catalytic depolymerisation,” Polym. Test., vol. 153, p. 109051, 2025, doi: 10.1016/j.polymertesting.2025.109051.

[7] E. McCrea, P. Goodrich, J. D. Holbrey, and M. Swadźba-Kwaśny, “Methanolysis of polyethylene terephthalate (PET) using non-stoichiometric protic ionic liquids,” RSC Sustain., vol. 3, no. 9, pp. 3987–3996, 2025, doi: 10.1039/D5SU00316D.

[8] G. Nayak and U. Y. Nayak, “Hot Melt Extrusion Technology in Taste Masking,” AAPS PharmSciTech, vol. 26, no. 196, 2025, doi: 10.1208/s12249-025-03174-9.

[9] P. Das, P. C. Nath, R. Singh, and Y. K. Mohanta, “Recent advances in extrusion technology for plant-based meat analogues: composition, development, and challenges,” European Food Research and Technology, vol. 252, no. 28, 2026, doi: 10.1007/s00217-025-05023-2.

[10] V. D. Berbentsev, “Hot Gas Extrusion—A New Technology of Metal Pressure Forming and Its Capabilities,” Steel Transl., vol. 55, no. 6, pp. 642–649, 2025, doi: 10.3103/S0967091225701256.

[11] I. L. Konstantinov et al., “Obtaining welding wire from alloy 1580 by technology including the method of combined rolling-extrusion,” Appl. Phys. A, vol. 130, no. 6, p. 403, 2024, doi: 10.1007/s00339-024-07580-x.

[12] Z. Li et al., “Strategies for Intelligent Detection and Fire Suppression of Lithium-Ion Batteries,” Electrochem. Energy Rev., vol. 7, no. 32, 2024, doi: 10.1007/s41918-024-00232-x.

[13] A. Yarahmadi, G. Zargar, S. Ashoori, and A. K. Manshad, “A comparative study of the rheological and adsorption behaviors of bio-and synthetic polymers for enhanced oil recovery,” Sci. Rep., vol. 15, no. 1, p. 44729, 2025, doi: 10.1038/s41598-025-28455-y.

[14] Y. B. Siyoum, F. G. Kindie, and M. A. Gebeyehu, “A review of current research and prospects of fused deposition modelling: application, materials, performance, process variables, parameter optimization, and numerical study,” Int. J. Adv. Manuf. Technol., vol. 138, no. 5–6, pp. 1675–1711, 2025, doi: 10.1007/s00170-025-15615-7.

[15] W. C. Titi, M. R. C. Achahuanco and J. T. Suarez, “Optimization of Temperature Control in Extrusion Machines Using Machine Learning Algorithms,” SSRG Int. J. Electron. Commun. Eng, vol. 16, no. 1, pp. 162–170, 2025.

[16] C. H. Tinh and V. X. Thin, “Synthesis of Proportional-Integral-Derivative Guidance Law for Homing Missiles Using the PSO Algorithm,” Russ. Aeronaut., vol. 68, no. 2, pp. 356–363, 2025, doi: 10.3103/S1068799825020126.

[17] K. Mou, et al., “Enhanced hippopotamus optimization algorithm for tuning proportional–integral–derivative controllers,” Front. Inf. Technol. Electron. Eng., vol. 26, no. 8, pp. 1356–1377, 2025, doi: 10.1631/FITEE.2400492.

[18] S. Chen, et al, “Accelerated optimization in deep learning with a proportional-integral-derivative controller,” Nat. Commun., vol. 15, no. 1, p. 10263, 2024, doi: 10.1038/s41467-024-54451-3.

[19] A. J, S. Giriprasad, M. S, and S. Gokul, “Optimized Nonlinear Time Delay System using Hybrid GOA-CVSTGCN Approach with Proportional Integral Derivative Controllers,” J. Vib. Eng. Technol., vol. 14, no. 30, 2025, doi: 10.1007/s42417-025-02212-x.

[20] F. Ben Aicha, “Optimized embedded AI: efficient implementation of CNNs on ESP32-CAM for real-time image classification,” Computing, vol. 107, no. 11, p. 206, 2025, doi: 10.1007/s00607-025-01559-z.

[21] H. H. and A. Setiawan, “Integrasi Sistem Keamanan Rumah Pintar Berbasis ESP32-CAM dan Sensor PIR dengan Notifikasi Real-Time melalui WhatsApp Bot,” SKANIKA Sist. Komput. dan Tek. Inform., vol. 8, pp. 204–218, 2025, doi: 10.36080/skanika.v8i2.3387.

[22] H. Y. Tsoo, T. M. Ting, and L. S. Chow, “Deployment of Speaker Identification System onto ESP32-DevKitC Microcontroller Using Neural Network and TensorFlow Lite,” SN Comput. Sci., vol. 6, no. 6, p. 736, 2025, doi: 10.1007/s42979-025-04270-0.

[23] I. P. Voronin, P. A. Voronin, and D. N. Bondarenko, “Basic Topologies of Quasi-Pulse-Width-Modulation Direct-Current Voltage Converters,” Russ. Electr. Eng., vol. 96, no. 9, pp. 763–767, 2025, doi: 10.3103/S1068371225701068.

[24] T. P. Sharma, et al., “Wi-Fi based quadcopter drone with battery monitoring and optimization using crazyflie platform,” Int. J. Inf. Technol., vol. 16, no. 3, pp. 1887–1898, 2024, doi: 10.1007/s41870-023-01639-3.

[25] R. Lafarge and A. Brosius, “Temperature control for thermomechanical ring rolling,” Prod. Eng., vol. 17, no. 6, pp. 907–914, 2023, doi: 10.1007/s11740-023-01213-7.

[26] M. I. Alam Shithil et al., “Performance enhancement of a vented quarter-circular solar thermal collector using proportional, proportional-integral, and proportional-integral-derivative controllers,” Appl. Therm. Eng., vol. 269, p. 126127, 2025, doi: 10.1016/j.applthermaleng.2025.126127.

[27] M. Xu and C. Chen, “Application and research of intelligent temperature control system based on deep learning in precision manufacturing product design,” Therm. Sci. Eng. Prog., vol. 57, p. 103185, 2025, doi: 10.1016/j.tsep.2024.103185.

[28] J.-S. Lin and K.-H. Chen, “A novel decision support system based on computational intelligence and machine learning: Towards zero-defect manufacturing in injection molding,” J. Ind. Inf. Integr., vol. 40, p. 100621, Jul. 2024, doi: 10.1016/j.jii.2024.100621.

[29] Y. Guo, Y. Zhang, Z. Pan, and W. Zhou, “Recent progress of sensing and machine learning technologies for process monitoring and defects detection in wire arc additive manufacturing,” J. Manuf. Process., vol. 125, pp. 489–511, 2024, doi: 10.1016/j.jmapro.2024.07.060.

Downloads

Published

2026-07-31

How to Cite

[1]
Y. Prabowo, A. Rifai, and J. Everhard, “RANCANG BANGUN SISTEM PENGENDALI SUHU BARREL PADA MESIN SINGLE SCREW EXTRUDER MENGGUNAKAN METODE PID BERBASIS ESP32”, SKANIKA, vol. 9, no. 2, pp. 192–201, Jul. 2026.

Issue

Vol. 9 No. 2 (2026): Jurnal SKANIKA Juli 2026 (In Press)

Section

Articles

License

Copyright (c) 2026 Yani Prabowo, Anwar Rifai, Jan Everhard

Creative Commons License

This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.

CC BY-SA 4.0

Creative Commons Attribution-ShareAlike 4.0 International

This license requires that reusers give credit to the creator. It allows reusers to distribute, remix, adapt, and build upon the material in any medium or format, even for commercial purposes. If others remix, adapt, or build upon the material, they must license the modified material under identical terms.

BY: Credit must be given to you, the creator.

SA: Adaptations must be shared under the same terms.ng